Image
Part Number -
T-WNB-3D-480
WattNode 480 VAC 3-phase Delta/Wye kWh Transducer Sensor
$395.00 USD
For sub-metering, net-metering, energy management, and performance contracting applications, the WattNode 480 VAC 3-phase Delta/Wye kWh Transducer Sensor works with Magnelab AC Current Transformers and a Pulse Input Adapter to provide True RMS kilowatt hours of energy used, even for loads with non-sinusoidal waveforms.
Overview
Provides accurate measurement at a low cost to meet your needs for sub-metering, net-metering, energy management, and performance contracting applications. This WattNode Delta or Wye-connection kWh Transducer works with Magnelab AC Current Transformers and a Pulse Input Adapter to provide True RMS kilowatt hours of energy used, even for loads with non-sinusoidal waveforms. Because these sensors tie directly into the line, they should only be used by qualified personnel. This model supports a 3-phase Delta-connection of 480 VAC.
Features
- Measures 1, 2, or 3 phases in 2, 3, or 4 wire configurations
- Use with wide choice of CTs (sold separately); ratings from 5 to 1500 amps
- Accurate measurement of 1-,2-, or 3-phase configurations
- Easy to install and wire
- Pulse output: compatible with pulse input logger models
- Small size: can be installed in existing service panels or junction boxes
- Diagnostic LEDs: confirms proper installation for all phases
- Bidirectional metering: net metering for PV (photovoltaic) solar and wind power generation with only one meter
- Metering of variable frequency drives
- Line powered: no external supply required
- Detachable terminal blocks: easy to install and remove.
- UL, cUL listed: designed and tested for safety and use throughout North America
- CE Mark: can be installed throughout the EU
Specifications
Operating: voltage range: ±20% of nominal
Frequency: 60 Hz
CT input: 0-0.5 VAC operating, 3 VAC maximum
Connectors: UL, CSA recognized, detachable screw terminals (14 AWG), 600V
Operating temp range: -30 to 60°C (-22 to 140°F)
Operating humidity range: 0 to 90% RH, non-condensing
Dimensions: 8.5 cm x 14.3 cm x 3.8 cm (3.3 in. x 5.6 in. x 1.5 in.)
Weight: 295 g (10.4 oz.)
Number of data channels: 2
To download the manual from Continental Control Systems LLC click here.
Below is a diagram of a typical installation
Image
- Delta or Wye configuration ranges: 480 Volts AC
- 3 Phase 3 Wire(No neutral)
- 3 Phase 4 Wire
- Accuracy: ±0.45% of reading + 0.05% FS through 25th harmonic
- (dependent on CT used and line variation accuracy could be 1.5% to 4% of reading)
Compatible items
AC Current
Pulse Input
Voltage Input Lead Set
Sensors
USB Data Loggers - requires external sensor(s)
USB Data Loggers - w/external sensor(s)
Web-based Monitoring Systems - via remote communication
Recently Viewed
Sensor
HWS Barometric Pressure Sensor
Provides average barometric pressure for each data logging interval over the range of 660 mb to 1070 mb (19.47 to 31.55 inHg); compatible with H22 data loggers.
Sensor
0 - 5 AMP Split-core AC Current Transformer Sensor
The Magnelab AC Current 0-5 Amp AC Current Transformer or CT (Magnelab part # SCT-0750-005) is mounted around a current carrying wire to measure AC Amperage. This CT provides 333mV output proportional to current and is used with the FlexSmart TRMS Module for True RMS measurement of sinusoidal and non-sinusoidal waveforms. The result is accurate current measurement for many types of equipment, including variable frequency drives and switched power sources. One or two CTs can be used with each FlexSmart TRMS Module.
